Planter Box Bracket Kits (5)

  Kit Includes: (2) Fixed Planter Box Brackets and (1) 16" or 24" Mounting Rail depending on length of your planter box - choose which best matches.   Fits any plastic/resin planter box tray that is 6 3/4" wide on the bottom (measure bottom of your box front to back). Use your own planter box or bring the planter box brackets to your favorite garden center and find the right fit!  Fits VERTICAL railing spindles that are built to code...which allows a 4" open space between the spindles, Hold It Mate fits up to a 5" open space.  Connects to a wide variety of spindles with our included hardware kits - no further tools needed.  From 1/2" to 1 3/4" spindle widths.  Wrought Iron is usually 1/2", Aluminum typically 3/4", PVC/Vinyl and Trex style are typically 1" -1 1/4" and finally wood can be 1 1/4" to 1 3/4"  - Simply use the bolt that is just a little longer than the thickness of the spindle...easy to find out which bolt to use by holding the bolts up against your spindles. Send us a message if you need further assistance! 

The best bracket kit to fit the widest variety of boxes!  Will hold a box that is 5 1/2" to 8 1/2" wide at the bottom (Measure front to back).  Choose between our new 16", 20" or 24" Option based on your planter box size.  Up to 24" Box for 16" and up to 36" for a 24" kit.  Fits round, square, aluminum, wood, PVC, wrought iron, recycled vertical spindles that are no further than 5" apart and are a 1/2" to 1 3/4" thick.  Code for the gap between spindles in the US is typically less than 4" - to which our systems were designed.   Measure before you order.   The mounting rail is the same Hold It Mate rail used for every other accessory and connects easily with the included Allen wrench in minutes and the shelf brackets just snap into place.  Once this is done, simply snap on the brackets, loosen the wing nuts on the bottom, drop your planted box on the brackets, then slide the brackets up snug to the box and tighten the wing nuts. Done!    Includes: (1) Hold It Mate mounting rail (16", 20" or 24"), (2) Adjustable Universal Planter Brackets

Want a shelf to hold beverages on your decks aluminum/wood/wrought iron/PVC railing?   Want a shelf between chairs on your balcony that doesn't take up so much space as a floor table does?  Want a side table for the grill?  Want a table that won't blow over in the wind?   Then this is what you need!   Fits round, square, aluminum, wood, PVC, wrought iron, recycled vertical spindles that are no further than 5" apart and are a 1/2" to 1 3/4" thick.  Code for the gap between spindles in the US is typically less than 4" - to which our systems were designed.   Measure the thickness of your spindles and the space between them before you order.  The mounting rail is the same Hold It Mate rail used for every other accessory and connects easily with the included Allen wrench in minutes and the shelf brackets just snap into place.  Once this is done, simply lay your wood shelf on the brackets, line up the shelf where you want it and mark the holes with a pencil - use screws that are about as long as your board is thick, no longer and with a screwdriver, screw 4 screws into the shelf - you are done!   Should take less than 15 minutes to install everything, it really is easy and simple.   Includes: (1) 16" or 24" Hold It Mate mounting rail, (2) - 10 1/2" Long Shelf brackets You will Need: 1 x 12 x 16" - 30" wood shelf depending on kit size (we recommend a cedar or sealing a pine board) (4) 3/4" wood screws that will fit through the shelf bracket holes, but not all the way through the wood top!   Also, see the tempered glass shelf a customer did in the photos, he placed rubber grippers under the glass and on the brackets to hold in place - beautiful look!   ReConnect with your Deck, with Hold It Mate!

Enjoy the ease of mounting a flat iron trough on your railings with Hold It Mate's Patented System!   ***Video shows the Mounting Rail, but different brackets - showing simply to show how easy it is to install*** Fits VERTICAL railing spindles that are built to code...which allows a 4" open space between the spindles.  Connects to a wide variety of spindles with our included hardware kits - no further tools needed.  From 1/2" to 1 3/4" spindle widths.  Wrought Iron is usually 1/2", Aluminum typically 3/4", PVC/Vinyl and Trex style are typically 1" -1 1/4" and finally wood can be 1 1/4" to 1 3/4"  - Simply use the bolt that is just a little longer than the thickness of the spindle...easy to find out which bolt to use by holding the bolts up against your spindles. Measure the thickness of your spindles and the open space between them before you order!  Send us a message if you need further assistance! Will hold ANY flat iron/metal cocoa lined trough style planter!   WAY better than zip tying to your railing!   Our patented system connects securely to your railing and your trough will simply hang on the hooks provided!  No zipping screws into your railing/deck posts, etc.  Installs in minutes with the included Allen wrench.   No harm to your railings at all!  Attach your mounting rail up high, down low or stack them for a full flowery look!   The design ability of these things is amazing!   Oh...and the hardware virtually disappears once you've placed your planter on the hooks!    Happy Planting!